San Gold Corporation TSX : SGR
Nasdaq OTCQX : SGRCF
December 20, 2011 09:22 ET
San Gold Reviews Over 200 Drill Holes from 2011 007 Zone Drilling
WINNIPEG, MANITOBA--(Marketwire - Dec. 20, 2011) - San Gold Corporation (TSX:SGR)(OTCQX:SGRCF) today announced the results of drilling conducted since January in the 007 Zone of the company's Rice Lake Mining Complex in Manitoba, Canada.
Drilling on the 007 Zone occurred throughout the year, from surface and underground drilling stations, in order to infill and extend the zone both along strike and to depth. At the beginning of 2011, the 007 Zone had a limited strike length of less than 200 m. A second new zone, then known as Emperor, was located approximately 300 m to the east along the same horizon. Drilling during the year to the east of 007 resulted first in the discovery of 007 East(730 zone) and then 007 Far East(740 zone). As drilling progressed during the year, it was determined that all four zones including the Emperor were part of a continuous stretch of mineralization extending about 500 m (1,640 feet) along strike.
Results obtained from the 2011 drilling program demonstrate consistent grades and widths throughout the 007 Zone, as highlighted by the following drill holes:
The 007 Zone is located along and within the Shoreline Basalt rock unit. San Gold views the full length of the Shoreline Basalt and similar parallel rock units as extremely prospective. In 2012, San Gold's drilling program will pursue the 007 Zone westward towards the L10 Zone, a region that has already returned encouraging results. San Gold will also pursue 007 to the east toward the SG-1 Zone, another Shoreline Basalt deposit located 2 km northeast of the 007 Zone. The region between 007 and SG-1 has yet to be significantly drill tested.
The drilling released today covers 261 intercepts over 215 drill holes within the 007 mineralized envelop. 17 of these holes have been released previously and are included here to provide a complete summary of the 007 drilling program in 2011. The full listing of the drill holes can be found in Table 1 of this release. Figures 1 to 5, which illustrate the location of drill holes and intercepts, can be found on the company web site (www.sangold.ca) and on SEDAR (www.sedar.com).
2011 Exploration Program
This drilling was carried out as part of San Gold's 2011 drill program. As of the end of October, the company had completed 300,000 metres of drilling within the Rice Lake Mining Complex. The Company's near-surface exploration activities in 2011 have focused on both exploration and definition drilling along the 007 Zone and within the L10, L13, SG-1 and Cohiba zones. Deep drilling has focused on extensions of the L10 and 007 zones, both from surface and from drilling stations on 16 Level and 26 Level in the Rice Lake Mine. Drilling within the Rice Lake Mine has focused primarily on definition drilling on 26, 28 and 31 Levels.
The surface drill program was carried out under the supervision of W.S. Ferreira, P.Geo., the Qualified Person for this project under National Instrument 43-101. The drill core was split, with half sent to TSL Laboratories in Saskatoon, SK and fire assayed with an AA and gravimetric finish. Whole metallic assays were performed on samples containing visible gold. Check assays were also performed on pulps and rejects by both TSL and by Accurassay Laboratories of Thunder Bay, ON. The underground drill program was carried out by San Gold mine geologists under the supervision of D. Ginn, P.Geo., the Qualified Person for San Gold under National Instrument 43-101. Underground drill core samples are assayed on site in the company's assay lab using the fire assay method with an AA and gravimetric finish. San Gold's quality control and assurance program includes the insertion of standards, the retention of pulps and rejects, and spot checks utilizing independent labs including TSL Laboratories in Saskatoon, SK and Accurassay Laboratories of Thunder Bay, ON. The core lengths are actual lengths as drilled and have not been adjusted for the true width of the mineralized zones.
About San Gold
San Gold is an established Canadian gold producer, explorer, and developer that owns and operates the Hinge, 007, and Rice Lake mines near Bissett, Manitoba. The Company employs more than 400 people and is committed to the highest standards of safety and environmental stewardship. San Gold is on the Toronto Stock Exchange under the symbol "SGR" and on the OTCQX under the symbol "SGRCF".
Cautionary Note
No stock exchange, securities commission or other regulatory authority has approved or disapproved the information contained herein. This news release includes certain "forward-looking statements". All statements, other than statements of historical fact included in this release, including, without limitation, statements regarding forecast gold production, gold grades, recoveries, cash operating costs, potential mineralization, mineral resources, mineral reserves, exploration results, and future plans and objectives of the Company, are forward-looking statements that involve various risks and uncertainties. These forward-looking statements include, but are not limited to, statements with respect to mining and processing of mined ore, achieving projected recovery rates, anticipated production rates and mine life, operating efficiencies, costs and expenditures, changes in mineral resources and conversion of mineral resources to proven and probable mineral reserves, and other information that is based on forecasts of future operational or financial results, estimates of amounts not yet determinable and assumptions of management.
Any statements that express or involve discussions with respect to predictions, expectations, beliefs, plans, projections, objectives, assumptions or future events or performance (often, but not always, using words or phrases such as "expects" or "does not expect", "is expected", "anticipates" or "does not anticipate", "plans", "estimates" or "intends", or stating that certain actions, events or results "may", "could", "would", "might" or "will" be taken, occur or be achieved) are not statements of historical fact and may be "forward-looking statements." Forward-looking statements are subject to a variety of risks and uncertainties that could cause actual events or results to differ from those reflected in the forward-looking statements.
There can be no assurance that forward-looking statements will prove to be accurate and actual results and future events could differ materially from those anticipated in such statements. Important factors that could cause actual results to differ materially from the Company's expectations include, among others, the actual results of current exploration activities, conclusions of economic evaluations and changes in project parameters as plans continue to be refined as well as future prices of precious metals, as well as those factors discussed in the section entitled "Other MD&A Requirements and Additional Disclosure and Risk Factors" in the Company's most recent quarterly Management's Analysis and Discussion ("MD&A"). Although the Company has attempted to identify important factors that could cause actual results to differ materially, there may be other factors that cause results not to be as anticipated, estimated or intended. There can be no assurance that such statements will prove to be accurate as actual results and future events could differ materially from those anticipated in such statements. Accordingly, readers should not place undue reliance on forward-looking statements.
Exploration results that include geophysics, sampling, and drill results on wide spacings may not be indicative of the occurrence of a mineral deposit. Such results do not provide assurance that further work will establish sufficient grade, continuity, metallurgical characteristics, and economic potential to be classed as a category of mineral resource. A mineral resource that is classified as "inferred" or "indicated" has a great amount of uncertainty as to its existence and economic and legal feasibility. It cannot be assumed that any or part of an "indicated mineral resource" or "inferred mineral resource" will ever be upgraded to a higher category of resource. Investors are cautioned not to assume that all or any part of mineral deposits in these categories will ever be converted into proven and probable reserves.
To view Figure 1, please visit the following link: http://media3.marketwire.com/docs/Figure_1-3D_view_west800.pdf.
To view Figure 2, please visit the following link: http://media3.marketwire.com/docs/Figure%202-007%20Long%20Section-3.pdf.
To view Figure 3, please visit the following link: http://media3.marketwire.com/docs/Figure_3-16_Level_Plan_View.pdf.
To view Figure 4, please visit the following link: http://media3.marketwire.com/docs/Figure_4-3D_view_south800.pdf.
To view Figure 5, please visit the following link: http://media3.marketwire.com/docs/Figure_5-3D_view_all800.pdf.
Drilling on the 007 Zone occurred throughout the year, from surface and underground drilling stations, in order to infill and extend the zone both along strike and to depth. At the beginning of 2011, the 007 Zone had a limited strike length of less than 200 m. A second new zone, then known as Emperor, was located approximately 300 m to the east along the same horizon. Drilling during the year to the east of 007 resulted first in the discovery of 007 East(730 zone) and then 007 Far East(740 zone). As drilling progressed during the year, it was determined that all four zones including the Emperor were part of a continuous stretch of mineralization extending about 500 m (1,640 feet) along strike.
Results obtained from the 2011 drilling program demonstrate consistent grades and widths throughout the 007 Zone, as highlighted by the following drill holes:
- S922-11-036, intersecting 23.2 g/tonne over 11.5 metres at a depth of 362 metres
- S922-11-013, intersecting 110.1 g/tonne over 2.1 metres at a depth of 330 metres
- S922-11-049, intersecting 44.2 g/tonne over 4.3 metres at a depth of 348 metres
- S922-11-089, intersecting 63.0 g/tonne over 2.8 metres at a depth of 362 metres
- S922-11-091, intersecting 21.7 g/tonne over 7.4 metres at a depth of 362 metres
- S915-11-003, intersecting 11.8 g/tonne over 12.3 metres at a depth of 396 metres
- S915-11-024, intersecting 60.7 g/tonne over 3.0 metres at a depth of 275 metres
- S915-11-045, intersecting 45.6 g/tonne over 4.3 metres at a depth of 291 metres
- S915-11-084, intersecting 17.4 g/tonne over 9.4 metres at a depth of 269 metres
- S915-11-106, intersecting 18.1 g/tonne over 3.2 metres at a depth of 358 metres
The 007 Zone is located along and within the Shoreline Basalt rock unit. San Gold views the full length of the Shoreline Basalt and similar parallel rock units as extremely prospective. In 2012, San Gold's drilling program will pursue the 007 Zone westward towards the L10 Zone, a region that has already returned encouraging results. San Gold will also pursue 007 to the east toward the SG-1 Zone, another Shoreline Basalt deposit located 2 km northeast of the 007 Zone. The region between 007 and SG-1 has yet to be significantly drill tested.
The drilling released today covers 261 intercepts over 215 drill holes within the 007 mineralized envelop. 17 of these holes have been released previously and are included here to provide a complete summary of the 007 drilling program in 2011. The full listing of the drill holes can be found in Table 1 of this release. Figures 1 to 5, which illustrate the location of drill holes and intercepts, can be found on the company web site (www.sangold.ca) and on SEDAR (www.sedar.com).
2011 Exploration Program
This drilling was carried out as part of San Gold's 2011 drill program. As of the end of October, the company had completed 300,000 metres of drilling within the Rice Lake Mining Complex. The Company's near-surface exploration activities in 2011 have focused on both exploration and definition drilling along the 007 Zone and within the L10, L13, SG-1 and Cohiba zones. Deep drilling has focused on extensions of the L10 and 007 zones, both from surface and from drilling stations on 16 Level and 26 Level in the Rice Lake Mine. Drilling within the Rice Lake Mine has focused primarily on definition drilling on 26, 28 and 31 Levels.
The surface drill program was carried out under the supervision of W.S. Ferreira, P.Geo., the Qualified Person for this project under National Instrument 43-101. The drill core was split, with half sent to TSL Laboratories in Saskatoon, SK and fire assayed with an AA and gravimetric finish. Whole metallic assays were performed on samples containing visible gold. Check assays were also performed on pulps and rejects by both TSL and by Accurassay Laboratories of Thunder Bay, ON. The underground drill program was carried out by San Gold mine geologists under the supervision of D. Ginn, P.Geo., the Qualified Person for San Gold under National Instrument 43-101. Underground drill core samples are assayed on site in the company's assay lab using the fire assay method with an AA and gravimetric finish. San Gold's quality control and assurance program includes the insertion of standards, the retention of pulps and rejects, and spot checks utilizing independent labs including TSL Laboratories in Saskatoon, SK and Accurassay Laboratories of Thunder Bay, ON. The core lengths are actual lengths as drilled and have not been adjusted for the true width of the mineralized zones.
About San Gold
San Gold is an established Canadian gold producer, explorer, and developer that owns and operates the Hinge, 007, and Rice Lake mines near Bissett, Manitoba. The Company employs more than 400 people and is committed to the highest standards of safety and environmental stewardship. San Gold is on the Toronto Stock Exchange under the symbol "SGR" and on the OTCQX under the symbol "SGRCF".
Cautionary Note
No stock exchange, securities commission or other regulatory authority has approved or disapproved the information contained herein. This news release includes certain "forward-looking statements". All statements, other than statements of historical fact included in this release, including, without limitation, statements regarding forecast gold production, gold grades, recoveries, cash operating costs, potential mineralization, mineral resources, mineral reserves, exploration results, and future plans and objectives of the Company, are forward-looking statements that involve various risks and uncertainties. These forward-looking statements include, but are not limited to, statements with respect to mining and processing of mined ore, achieving projected recovery rates, anticipated production rates and mine life, operating efficiencies, costs and expenditures, changes in mineral resources and conversion of mineral resources to proven and probable mineral reserves, and other information that is based on forecasts of future operational or financial results, estimates of amounts not yet determinable and assumptions of management.
Any statements that express or involve discussions with respect to predictions, expectations, beliefs, plans, projections, objectives, assumptions or future events or performance (often, but not always, using words or phrases such as "expects" or "does not expect", "is expected", "anticipates" or "does not anticipate", "plans", "estimates" or "intends", or stating that certain actions, events or results "may", "could", "would", "might" or "will" be taken, occur or be achieved) are not statements of historical fact and may be "forward-looking statements." Forward-looking statements are subject to a variety of risks and uncertainties that could cause actual events or results to differ from those reflected in the forward-looking statements.
There can be no assurance that forward-looking statements will prove to be accurate and actual results and future events could differ materially from those anticipated in such statements. Important factors that could cause actual results to differ materially from the Company's expectations include, among others, the actual results of current exploration activities, conclusions of economic evaluations and changes in project parameters as plans continue to be refined as well as future prices of precious metals, as well as those factors discussed in the section entitled "Other MD&A Requirements and Additional Disclosure and Risk Factors" in the Company's most recent quarterly Management's Analysis and Discussion ("MD&A"). Although the Company has attempted to identify important factors that could cause actual results to differ materially, there may be other factors that cause results not to be as anticipated, estimated or intended. There can be no assurance that such statements will prove to be accurate as actual results and future events could differ materially from those anticipated in such statements. Accordingly, readers should not place undue reliance on forward-looking statements.
Exploration results that include geophysics, sampling, and drill results on wide spacings may not be indicative of the occurrence of a mineral deposit. Such results do not provide assurance that further work will establish sufficient grade, continuity, metallurgical characteristics, and economic potential to be classed as a category of mineral resource. A mineral resource that is classified as "inferred" or "indicated" has a great amount of uncertainty as to its existence and economic and legal feasibility. It cannot be assumed that any or part of an "indicated mineral resource" or "inferred mineral resource" will ever be upgraded to a higher category of resource. Investors are cautioned not to assume that all or any part of mineral deposits in these categories will ever be converted into proven and probable reserves.
| Table 1: Full Listing of 007 Drilling Results (January-October 2011) (1) |
| Depth | From | To | Length | Au | |
| Drill Hole | metres | g/tonne | |||
| Drilling Station 007-S915 UG | |||||
| S915-11-001 | 200.3 | 65.7 | 66.0 | 0.3 | 3.2 |
| S915-11-002 | 197.0 | 88.7 | 89.4 | 0.6 | 0.0 |
| S915-11-003 | 395.9 | 157.6 | 169.9 | 12.3 | 11.8 |
| S915-11-004 | 228.0 | 59.6 | 60.1 | 0.5 | 2.2 |
| S915-11-006 | 280.9 | 75.6 | 76.5 | 0.9 | 0.3 |
| S915-11-007 | 296.1 | 78.9 | 82.0 | 3.1 | 17.8 |
| and | 55.3 | 62.5 | 7.3 | 2.0 | |
| S915-11-008 | 314.6 | 96.3 | 120.2 | 23.9 | 1.3 |
| incl | 117.8 | 120.2 | 2.4 | 3.9 | |
| and | 59.3 | 71.3 | 12.0 | 4.3 | |
| S915-11-009 | 207.3 | 55.3 | 61.0 | 5.7 | 4.3 |
| incl | 55.3 | 56.1 | 0.8 | 7.5 | |
| incl | 58.6 | 59.0 | 0.3 | 29.1 | |
| S915-11-010 | 217.3 | 46.0 | 58.2 | 12.2 | 5.1 |
| incl | 50.0 | 56.4 | 6.4 | 9.0 | |
| S915-11-011 | 33.7 | 37.1 | 3.4 | 2.2 | |
| incl | 34.1 | 34.9 | 0.8 | 7.4 | |
| incl | 36.8 | 37.1 | 0.3 | 3.6 | |
| and | 226.6 | 42.0 | 55.2 | 13.2 | 11.6 |
| incl | 49.5 | 55.2 | 5.7 | 24.5 | |
| S915-11-013 | 243.4 | 33.4 | 43.8 | 10.4 | 7.6 |
| incl | 33.8 | 43.8 | 10.0 | 7.2 | |
| incl | 43.2 | 43.8 | 0.6 | 67.2 | |
| S915-11-014 | 278.3 | 50.7 | 63.2 | 12.5 | 11.6 |
| incl | 54.7 | 56.4 | 1.7 | 58.9 | |
| S915-11-015 | 293.2 | 69.4 | 74.6 | 5.2 | 2.2 |
| S915-11-016 | 304.5 | 76.2 | 84.2 | 8.0 | 15.3 |
| S915-11-017 | 331.6 | 99.3 | 103.1 | 3.8 | 8.0 |
| and | 345.6 | 115.6 | 124.7 | 9.1 | 13.1 |
| S915-11-019 | 211.8 | 48.6 | 51.8 | 3.2 | 3.8 |
| S915-11-020 | 221.6 | 44.3 | 46.8 | 2.4 | 4.9 |
| S915-11-022 | 242.6 | 41.4 | 43.4 | 2.1 | 4.5 |
| S915-11-023 | No Significant Results | ||||
| S915-11-024 | 274.5 | 50.0 | 52.9 | 3.0 | 60.7 |
| S915-11-026 | 289.9 | 56.8 | 60.2 | 3.4 | 7.1 |
| S915-11-027 | 313.3 | 75.1 | 78.9 | 3.8 | 4.6 |
| and | 322.8 | 87.8 | 91.6 | 3.8 | 6.0 |
| S915-11-028 | 52.1 | 52.4 | 0.4 | 3.6 | |
| and | 203.3 | 62.0 | 63.2 | 1.2 | 0.9 |
| S915-11-030 | 33.2 | 37.8 | 4.6 | 7.2 | |
| incl | 37.3 | 37.8 | 0.5 | 57.6 | |
| and | 42.7 | 43.9 | 1.2 | 4.7 | |
| and | 224.5 | 47.3 | 51.2 | 3.8 | 58.3 |
| incl | 49.0 | 49.3 | 0.3 | 607.4 | |
| S915-11-032 | 34.1 | 36.2 | 2.1 | 4.3 | |
| and | 243.5 | 39.2 | 45.7 | 6.5 | 6.2 |
| incl | 39.2 | 40.7 | 1.5 | 17.5 | |
| S915-11-033 | 258.5 | 128.4 | 130.3 | 1.9 | 72.7 |
| incl | 128.4 | 128.9 | 0.5 | 282.1 | |
| and | 257.7 | 133.4 | 142.1 | 8.7 | 7.9 |
| incl | 133.4 | 137.3 | 3.9 | 3.8 | |
| incl | 135.7 | 137.3 | 1.6 | 7.0 | |
| incl | 138.8 | 142.1 | 3.3 | 16.5 | |
| incl | 138.8 | 140.5 | 1.7 | 30.0 | |
| and | 149.5 | 150.5 | 1.0 | 4.9 | |
| S915-11-034 | 272.5 | 39.0 | 50.3 | 11.3 | 11.5 |
| S915-11-035 | 291.9 | 57.0 | 62.6 | 5.6 | 7.6 |
| S915-11-037 | 316.5 | 79.7 | 84.1 | 4.4 | 5.9 |
| S915-11-038 | 42.4 | 45.2 | 2.8 | 3.1 | |
| incl | 44.6 | 45.2 | 0.6 | 8.7 | |
| and | 203.7 | 56.3 | 67.1 | 10.8 | 13.2 |
| incl | 57.5 | 58.1 | 0.6 | 31.4 | |
| incl | 63.1 | 65.3 | 2.2 | 42.1 | |
| S915-11-040 | 226.4 | 41.1 | 49.5 | 8.4 | 14.3 |
| incl | 47.8 | 49.0 | 1.2 | 93.7 | |
| S915-11-042 | 240.5 | 41.6 | 44.4 | 2.8 | 33.6 |
| S915-11-043 | 275.3 | 45.4 | 52.8 | 7.4 | 14.8 |
| S915-11-045 | 290.8 | 56.9 | 61.2 | 4.3 | 45.6 |
| S915-11-047 | 317.0 | 78.3 | 89.8 | 11.5 | 9.5 |
| incl | 79.7 | 87.4 | 7.7 | 11.6 | |
| S915-11-048 | 55.0 | 56.2 | 1.2 | 8.0 | |
| and | 197.4 | 66.8 | 72.1 | 5.3 | 80.4 |
| incl | 66.9 | 70.3 | 3.4 | 119.9 | |
| S915-11-050 | 16.2 | 18.1 | 1.9 | 4.6 | |
| and | 223.4 | 52.2 | 57.0 | 4.8 | 43.5 |
| incl | 55.6 | 57.0 | 1.4 | 144.2 | |
| S915-11-052 | 241.5 | 47.0 | 52.2 | 5.2 | 2.7 |
| incl | 47.0 | 47.5 | 0.5 | 8.6 | |
| and | 240.2 | 54.2 | 54.8 | 0.6 | 13.4 |
| S915-11-054 | 274.7 | 57.8 | 60.0 | 2.2 | 6.3 |
| S915-11-055 | 320.6 | 111.9 | 114.4 | 2.5 | 6.3 |
| S915-11-056 | 372.5 | 169.3 | 170.6 | 1.3 | 3.7 |
| S915-11-057 | 233.5 | 151.0 | 155.8 | 4.8 | 7.7 |
| S915-11-058 | 221.0 | 86.1 | 86.5 | 0.3 | 59.3 |
| S915-11-059 | 240.9 | 62.5 | 62.5 | 0.0 | 0.0 |
| and | 93.5 | 94.5 | 1.0 | 7.1 | |
| S915-11-060 | 248.7 | 94.9 | 95.1 | 0.2 | 0.0 |
| S915-11-061 | 262.2 | 66.8 | 67.5 | 0.7 | 0.0 |
| S915-11-062 | 275.6 | 111.6 | 121.9 | 10.3 | 17.0 |
| incl | 115.0 | 118.2 | 3.2 | 42.2 | |
| S915-11-063 | No Significant Results | ||||
| S915-11-065 | No Significant Results | ||||
| S915-11-064 | 228.3 | 41.3 | 41.9 | 0.6 | 0.2 |
| S915-11-066 | 217.0 | 51.9 | 54.3 | 2.3 | 0.3 |
| S915-11-067 | 227.6 | 44.2 | 49.0 | 4.7 | 1.6 |
| S915-11-068 | 202.2 | 61.6 | 64.5 | 2.9 | 4.4 |
| S915-11-069 | 226.9 | 37.9 | 41.6 | 3.7 | 0.7 |
| and | 219.2 | 52.0 | 53.4 | 1.5 | 3.5 |
| S915-11-070 | 230.8 | 35.8 | 36.6 | 0.7 | 0.0 |
| S915-11-071 | 210.0 | 49.5 | 51.7 | 2.3 | 3.4 |
| S915-11-072 | 228.0 | 32.8 | 33.2 | 0.4 | 41.7 |
| S915-11-073 | 229.2 | 44.0 | 47.4 | 3.5 | 0.4 |
| S915-11-074 | 208.2 | 50.0 | 52.9 | 2.8 | 3.9 |
| S915-11-075 | 213.7 | 52.0 | 53.8 | 1.8 | 3.8 |
| S915-11-076 | 245.4 | 12.5 | 13.9 | 1.4 | 4.1 |
| and | 230.7 | 40.7 | 41.6 | 1.0 | 1.3 |
| S915-11-077 | 235.1 | 35.7 | 41.1 | 5.5 | 2.0 |
| incl | 35.7 | 37.8 | 2.1 | 3.6 | |
| S915-11-078 | 263.7 | 40.3 | 45.0 | 4.7 | 2.5 |
| and | 269.1 | 64.2 | 65.7 | 1.6 | 2.6 |
| S915-11-079 | No Significant Results | 0.0 | |||
| S915-11-080 | 207.9 | 68.5 | 73.5 | 4.9 | 3.2 |
| incl | 69.9 | 72.8 | 2.9 | 5.2 | |
| and | 224.5 | 41.8 | 44.9 | 3.2 | 2.3 |
| S915-11-081 | 235.3 | 52.7 | 55.4 | 2.8 | 1.8 |
| S915-11-082 | 265.2 | 49.7 | 50.7 | 1.0 | 2.8 |
| S915-11-083 | 285.6 | 68.6 | 69.6 | 1.0 | 0.0 |
| S915-11-084 | 268.6 | 48.4 | 57.9 | 9.4 | 17.4 |
| incl | 48.4 | 52.1 | 3.7 | 35.6 | |
| incl | 54.3 | 56.7 | 2.5 | 12.9 | |
| and | 272.1 | 62.6 | 67.8 | 5.2 | 33.7 |
| S915-11-085 | No Significant Results | ||||
| S915-11-086 | No Significant Results | ||||
| S915-11-087 | No Significant Results | ||||
| S915-11-088 | No Significant Results | ||||
| S915-11-089 | 250.5 | 6.8 | 9.0 | 2.2 | 0.3 |
| S915-11-090 | No Significant Results | ||||
| S915-11-091 | 250.5 | 27.6 | 30.1 | 2.5 | 0.3 |
| S915-11-092 | 262.9 | 33.9 | 35.2 | 1.3 | 36.2 |
| and | 267.4 | 50.3 | 50.5 | 0.3 | 17.7 |
| S915-11-093 | 261.5 | 30.0 | 30.7 | 0.7 | 34.0 |
| and | 263.7 | 36.1 | 37.6 | 1.5 | 3.9 |
| and | 266.7 | 45.7 | 46.7 | 1.0 | 51.7 |
| S915-11-094 | 260.6 | 24.2 | 27.4 | 3.3 | 7.7 |
| and | 267.0 | 39.4 | 47.7 | 8.2 | 58.4 |
| incl | 43.9 | 47.7 | 3.7 | 124.8 | |
| S915-11-100 | 330.1 | 130.5 | 131.4 | 0.9 | 0.3 |
| S915-11-102 | 193.5 | 75.4 | 77.1 | 1.6 | 1.8 |
| S915-11-105 | 339.5 | 108.7 | 113.4 | 4.7 | 20.3 |
| S915-11-106 | 357.5 | 124.2 | 127.4 | 3.2 | 18.1 |
| S915-11-107 | 345.9 | 106.8 | 111.7 | 4.9 | 29.2 |
| S915-11-108 | 347.2 | 103.2 | 110.2 | 7.0 | 9.2 |
| S915-11-109 | 351.7 | 110.1 | 112.0 | 1.9 | 1.7 |
| S915-11-110 | 373.1 | 134.8 | 136.7 | 1.9 | 15.7 |
| Drilling Station 007-S922 UG | |||||
| S922-11-001 | 300.8 | 126.5 | 128.4 | 1.9 | 0.1 |
| S922-11-002 | 312.3 | 118.7 | 119.9 | 1.3 | 48.6 |
| S922-11-003 | 328.8 | 121.0 | 122.8 | 1.7 | 16.3 |
| S922-11-004 | 300.2 | 114.7 | 117.0 | 2.3 | 7.6 |
| S922-11-005 | 315.2 | 115.1 | 117.3 | 2.2 | 1.7 |
| S922-11-007 | 297.5 | 117.0 | 118.8 | 1.8 | 1.4 |
| S922-11-008 | 308.5 | 116.0 | 118.9 | 2.8 | 0.8 |
| S922-11-009 | 324.0 | 117.5 | 120.1 | 2.6 | 1.6 |
| S922-11-010 | 300.8 | 110.2 | 112.3 | 2.1 | 0.3 |
| S922-11-011 | 312.7 | 109.9 | 113.3 | 3.4 | 4.0 |
| S922-11-012 | 311.2 | 112.0 | 112.7 | 0.7 | 7.1 |
| S922-11-013 | 329.8 | 117.0 | 119.1 | 2.1 | 110.1 |
| S922-11-014 | 298.1 | 115.3 | 116.6 | 1.3 | 12.2 |
| S922-11-015 | 321.6 | 111.7 | 114.8 | 3.2 | 3.1 |
| S922-11-016 | 310.9 | 120.8 | 129.4 | 8.6 | 0.6 |
| S922-11-017 | 333.1 | 128.9 | 132.3 | 3.5 | 4.0 |
| S922-11-018 | 300.5 | 137.9 | 139.4 | 1.5 | 0.2 |
| S922-11-019 | 311.2 | 122.8 | 127.0 | 4.3 | 2.3 |
| S922-11-020 | 321.4 | 118.3 | 120.5 | 2.2 | 1.5 |
| S922-11-021 | 290.6 | 144.8 | 145.6 | 0.8 | 6.1 |
| and | 296.6 | 160.4 | 161.1 | 0.7 | 24.8 |
| S922-11-022 | 321.2 | 157.2 | 159.9 | 2.7 | 4.8 |
| S922-11-023 | 331.9 | 148.9 | 153.0 | 4.1 | 2.3 |
| incl | 151.6 | 152.8 | 1.1 | 6.1 | |
| S922-11-024 | 295.1 | 147.2 | 151.3 | 4.1 | 4.7 |
| S922-11-025 | 315.8 | 155.0 | 157.0 | 2.0 | 5.7 |
| S922-11-026 | 331.9 | 180.9 | 189.3 | 8.5 | 4.2 |
| incl | 180.9 | 181.6 | 0.8 | 11.6 | |
| incl | 184.6 | 185.8 | 1.2 | 16.4 | |
| S922-11-029 | 327.2 | 178.6 | 183.1 | 4.5 | 5.5 |
| S922-11-030 | 349.8 | 131.2 | 134.0 | 2.8 | 8.2 |
| incl | 131.2 | 131.5 | 0.3 | 62.3 | |
| S922-11-034 | 57.6 | 57.8 | 0.2 | 12.0 | |
| and | 124.1 | 126.9 | 2.8 | 1.3 | |
| S922-11-035 | 338.6 | 119.7 | 122.6 | 2.9 | 11.4 |
| S922-11-036 | 362.4 | 132.3 | 143.8 | 11.5 | 23.2 |
| incl | 132.3 | 140.0 | 7.7 | 33.0 | |
| S922-11-038 | 290.2 | 157.5 | 158.5 | 1.0 | 2.6 |
| and | 170.0 | 170.7 | 0.6 | 5.5 | |
| S922-11-039 | 326.7 | 154.0 | 154.3 | 0.3 | 1.0 |
| and | 329.4 | 158.9 | 159.6 | 0.7 | 0.9 |
| S922-11-040 | 136.7 | 137.3 | 0.7 | 3.6 | |
| and | 343.0 | 146.2 | 149.9 | 3.7 | 6.9 |
| incl | 146.9 | 149.9 | 3.0 | 8.7 | |
| S922-11-042 | 343.0 | 154.5 | 154.6 | 0.0 | 0.0 |
| and | 175.0 | 178.5 | 3.5 | 2.7 | |
| and | 175.0 | 175.6 | 0.6 | 6.9 | |
| and | 176.9 | 177.5 | 0.7 | 3.9 | |
| S922-11-043 | 282.2 | 171.0 | 176.9 | 5.9 | 9.2 |
| S922-11-044 | 301.8 | 148.4 | 151.6 | 3.2 | 5.2 |
| S922-11-045 | 333.1 | 156.0 | 157.3 | 1.3 | 4.6 |
| S922-11-046 | 343.5 | 150.9 | 157.5 | 6.6 | 1.3 |
| S922-11-047 | 351.1 | 133.2 | 134.1 | 0.9 | 185.3 |
| and | 362.5 | 144.8 | 148.5 | 3.7 | 11.4 |
| S922-11-048 | 372.5 | 147.5 | 148.6 | 1.2 | 1.1 |
| S922-11-049 | 348.1 | 132.6 | 136.8 | 4.3 | 44.2 |
| S922-11-050 | 364.5 | 144.4 | 144.6 | 0.2 | 0.1 |
| S922-11-051 | 358.7 | 143.5 | 146.2 | 2.7 | 11.1 |
| S922-11-052 | 349.9 | 148.0 | 149.2 | 1.2 | 0.6 |
| S922-10-054 | 250.2 | 147.5 | 151.1 | 3.6 | 8.6 |
| incl | 148.2 | 150.4 | 2.2 | 10.5 | |
| S922-11-055 | 351.7 | 138.0 | 140.8 | 2.8 | 3.2 |
| S922-11-057 | 293.8 | 107.5 | 110.8 | 3.3 | 3.7 |
| S922-11-058 | 211.5 | 198.6 | 200.1 | 1.5 | 23.9 |
| incl | 199.2 | 199.4 | 0.2 | 159.4 | |
| S922-11-061 | 344.4 | 125.9 | 129.0 | 3.1 | 28.6 |
| S922-11-062 | 321.9 | 131.7 | 133.0 | 1.3 | 3.9 |
| S922-11-064 | 341.1 | 136.2 | 142.0 | 5.8 | 1.1 |
| S922-11-065 | 358.4 | 139.0 | 141.6 | 2.6 | 3.3 |
| incl | 175.9 | 176.6 | 0.7 | 161.6 | |
| S922-11-072 | 279.2 | 175.5 | 177.8 | 2.3 | 5.9 |
| S922-11-076 | 305.5 | 146.1 | 147.1 | 1.0 | 5.2 |
| incl | 146.4 | 146.7 | 0.3 | 8.5 | |
| and | 309.3 | 155.4 | 156.4 | 1.0 | 4.0 |
| incl | 155.4 | 155.7 | 0.3 | 11.6 | |
| S922-11-078 | 231.3 | 174.5 | 177.5 | 3.0 | 20.5 |
| S922-11-079 | 378.6 | 161.9 | 164.4 | 2.5 | 6.8 |
| S922-11-080 | 322.3 | 117.5 | 118.0 | 0.4 | 0.2 |
| S922-11-081 | 323.7 | 106.9 | 109.7 | 2.8 | 0.1 |
| S922-11-082 | 361.8 | 136.5 | 138.0 | 1.6 | 24.1 |
| S922-11-084 | 373.4 | 143.1 | 144.3 | 1.1 | 13.0 |
| and | 384.4 | 154.7 | 156.7 | 2.0 | 5.9 |
| S922-11-085 | 350.5 | 130.1 | 132.1 | 2.0 | 10.2 |
| incl | 350.0 | 130.1 | 131.0 | 0.9 | 22.4 |
| S922-11-086 | 381.0 | 150.5 | 152.1 | 1.6 | 7.3 |
| and | 392.6 | 161.6 | 164.2 | 2.6 | 0.2 |
| S922-11-087 | 272.8 | 48.5 | 51.5 | 3.0 | 3.9 |
| and | 327.7 | 119.5 | 122.2 | 2.7 | 0.4 |
| S922-11-088 | 345.8 | 126.8 | 130.3 | 3.5 | 7.2 |
| S922-11-089 | 361.6 | 136.7 | 139.4 | 2.8 | 63.0 |
| incl | 136.7 | 137.4 | 0.7 | 240.5 | |
| and | 365.8 | 142.0 | 143.6 | 1.6 | 10.5 |
| incl | 142.9 | 143.6 | 0.7 | 22.4 | |
| and | 369.8 | 146.5 | 148.0 | 1.5 | 5.5 |
| incl | 146.5 | 146.9 | 0.4 | 17.5 | |
| S922-11-090 | 347.5 | 124.5 | 128.0 | 3.5 | 1.8 |
| S922-11-091 | 362.2 | 135.6 | 143.0 | 7.4 | 21.7 |
| incl | 135.6 | 137.9 | 2.3 | 18.3 | |
| incl | 139.9 | 141.8 | 2.0 | 59.2 | |
| S922-11-092 | 374.9 | 143.0 | 153.2 | 10.2 | 1.9 |
| incl | 143.4 | 147.1 | 3.7 | 4.5 | |
| S922-11-093 | 371.4 | 140.9 | 145.3 | 4.4 | 14.6 |
| and | 378.9 | 149.9 | 152.4 | 2.5 | 3.2 |
| S922-11-094 | 404.5 | 174.5 | 177.3 | 2.8 | 2.1 |
| S922-11-095 | 381.5 | 147.0 | 149.0 | 2.0 | 0.8 |
| S922-11-096 | 359.4 | 134.8 | 137.3 | 2.5 | 23.6 |
| S922-11-097 | 375.2 | 144.2 | 149.5 | 5.3 | 19.5 |
| and | 383.7 | 154.8 | 157.8 | 3.0 | 7.6 |
| S922-11-098 | 305.8 | 144.2 | 148.3 | 4.1 | 4.1 |
| S922-11-099 | 311.2 | 138.2 | 139.6 | 1.5 | 4.0 |
| and | 314.9 | 144.6 | 146.6 | 2.0 | 4.8 |
| S922-11-100 | 334.4 | 135.5 | 139.7 | 4.1 | 1.8 |
| S922-11-101 | 349.3 | 139.2 | 143.3 | 4.0 | 13.0 |
| S922-11-102 | 365.4 | 141.5 | 146.4 | 4.9 | 1.3 |
| S922-11-103 | 336.2 | 135.1 | 139.6 | 4.5 | 7.3 |
| S922-11-104 | 352.3 | 136.3 | 138.5 | 2.2 | 2.4 |
| Drilling Station Surface DDH 007 | |||||
| CD-11-162 | No Significant Results | 0.0 | |||
| CD-11-165 | No Significant Results | 0.0 | |||
| CD-11-166 | No Significant Results | 0.0 | |||
| CD-11-169 | 269.1 | 279.5 | 284.8 | 5.3 | 0.9 |
| and | 281.1 | 293.8 | 295.5 | 1.7 | 10.7 |
| incl | 293.8 | 294.7 | 0.9 | 18.4 | |
| CD-11-200 | 144.8 | 199.5 | 205.1 | 5.6 | 0.0 |
| CD-11-202 | 205.1 | 223.8 | 233.9 | 10.1 | 0.5 |
| incl | 230.7 | 231.3 | 0.6 | 5.3 | |
| CD-11-204 | 196.8 | 217.8 | 218.0 | 0.2 | 0.1 |
| CD-11-205 | 199.9 | 222.6 | 223.7 | 1.1 | 5.5 |
| CD-11-206 | 225.6 | 242.1 | 243.0 | 0.9 | 7.0 |
| incl | 242.7 | 243.0 | 0.3 | 17.1 | |
| CD-11-207 | 184.7 | 221.6 | 225.0 | 3.4 | 0.6 |
| incl | 224.6 | 225.0 | 0.5 | 4.4 | |
| CD-11-208 | 172.2 | 222.9 | 224.5 | 1.6 | 0.6 |
| CD-11-209 | 178.3 | 217.9 | 218.1 | 0.2 | 2.4 |
| CD-11-210 | 173.7 | 218.5 | 219.3 | 0.7 | 1.9 |
| CD-11-211 | 156.7 | 213.8 | 215.6 | 1.9 | 0.0 |
| CD-11-212 | 151.8 | 195.2 | 195.7 | 0.5 | 10.8 |
| CD-11-217 | 162.5 | 205.8 | 206.9 | 1.1 | 11.1 |
| CD-11-218 | 149.7 | 198.2 | 200.5 | 2.2 | 3.7 |
| CD-11-222 | 147.9 | 196.1 | 198.5 | 2.3 | 0.3 |
| CD-11-223 | 142.6 | 196.2 | 197.8 | 1.6 | 0.5 |
| CD-11-227 | No Significant Results | ||||
| CD-11-228 | 184.1 | 218.0 | 221.7 | 3.7 | 4.6 |
| CD-11-232 | 178.9 | 215.6 | 216.6 | 0.9 | 0.5 |
| CD-11-230 | 218.2 | 235.8 | 239.1 | 3.3 | 2.2 |
| CD-11-233 | 200.9 | 218.5 | 219.5 | 0.9 | 0.1 |
| CD-11-234 | 202.4 | 225.1 | 225.3 | 0.2 | 2.4 |
| CD-11-235 | 188.7 | 213.8 | 214.2 | 0.4 | 0.4 |
| CD-11-236 | 172.2 | 203.9 | 204.5 | 0.6 | 9.8 |
| CD-11-238 | 121.6 | 136.8 | 142.2 | 5.4 | 0.0 |
| CD-11-241 | 227.1 | 242.7 | 249.6 | 6.9 | 7.9 |
| and | 261.5 | 280.5 | 283.8 | 3.3 | 10.6 |
| CD-11-242 | 192.9 | 216.1 | 218.7 | 2.6 | 0.9 |
| CD-11-244 | 112.7 | 137.8 | 139.3 | 1.5 | 0.4 |
| CD-11-245 | 236.5 | 259.1 | 260.3 | 1.2 | 5.2 |
| CD-11-246 | 239.0 | 265.6 | 266.9 | 1.3 | 4.3 |
| CD-11-248 | 157.0 | 188.1 | 191.4 | 3.3 | 0.2 |
| CD-11-250 | 157.9 | 198.0 | 201.0 | 3.0 | 1.1 |
| CD-11-251 | 138.7 | 187.1 | 190.7 | 3.5 | 1.1 |
| CD-11-252 | 139.9 | 206.6 | 209.7 | 3.1 | 0.0 |
| CD-11-253 | 121.7 | 199.5 | 202.4 | 2.9 | 4.6 |
| incl | 120.9 | 199.5 | 199.7 | 0.2 | 45.3 |
| CD-11-254 | 152.9 | 202.7 | 205.0 | 2.3 | 0.3 |
| CD-11-255 | 133.5 | 187.1 | 189.5 | 2.4 | 0.0 |
| CD-11-257 | 119.5 | 199.6 | 202.5 | 3.0 | 8.2 |
| incl | 199.6 | 199.8 | 0.2 | 120.4 | |
| CD-11-259 | 127.4 | 189.4 | 190.8 | 1.4 | 10.9 |
| CD-11-262 | 320.8 | 336.9 | 345.6 | 8.7 | 3.8 |
| incl | 339.2 | 343.0 | 3.8 | 7.4 | |
| JH-11-019 | 361.7 | 472.4 | 474.9 | 2.5 | 20.3 |
| JH-11-026 | 326.1 | 456.6 | 458.0 | 1.4 | 7.6 |
| JH-11-028 | 370.9 | 473.1 | 475.7 | 2.6 | 18.6 |
| and | 374.9 | 478.8 | 480.3 | 1.6 | 2.3 |
| JH-11-030 | 394.3 | 522.9 | 525.0 | 2.2 | 2.2 |
| JH-11-055 | 435.0 | 521.9 | 526.4 | 4.5 | 5.1 |
| (1) Due to the exploratory nature of this exploration program and the variable orientations of the high-grade mineralized zones, the intersections presented herein may not necessarily represent the true width of mineralization. |
To view Figure 2, please visit the following link: http://media3.marketwire.com/docs/Figure%202-007%20Long%20Section-3.pdf.
To view Figure 3, please visit the following link: http://media3.marketwire.com/docs/Figure_3-16_Level_Plan_View.pdf.
To view Figure 4, please visit the following link: http://media3.marketwire.com/docs/Figure_4-3D_view_south800.pdf.
To view Figure 5, please visit the following link: http://media3.marketwire.com/docs/Figure_5-3D_view_all800.pdf.
The TSX and the OTCQX exchanges have not reviewed and do not accept responsibility for the adequacy or accuracy of this release.
Contact Information
San Gold Corporation
Tim Friesen
Communications Director
1 (204) 772-9149 ext. 202
San Gold Corporation
George Pirie
President and CEO
1 (416) 214-0024
www.sangold.ca
No comments:
Post a Comment